D1063S G.M. International s.r.l.
GM International

  • Search
  • RESERVED AREA
    Lost Password
    Not registered yet?
    Sign up

D1063S

  1. Products
  2. Intrinsically Safe Isolators
  3. Load Cell Input
D1063S
Load Cell/Strain Gauge Bridge Isolating Repeater DIN-Rail Model D1063S

The single channel DIN Rail Load Cell/Strain Gauge Bridge Isolating Repeater D1063S acts as a transparent galvanic isolated interface installed between a weighing indicator in Safe Area and a load cell (or group of load cells) in Hazardous Area; it appears at the terminals of the indicator as a single load cell equivalent to the one in the field. Provides a fully floating power supply voltage with remote sensing capability to load cell located in Hazardous Area and repeats, while isolating, the mV signal output to drive a load in Safe Area depending on the host system reference voltage. Up to four 350 Ω load cells, or six 450 Ω load cells, or twelve 1000 Ω load cells can be connected in parallel. Voltage reference (Safe Area side) is DIP switch configurable to select internal or external (host system) supply. In addition a field wiring fault red LED indicates any wire break in the Hazardous Area side.

FEATURES

  • Input from Zone 0 (Zone 20), Division 1, installation in Zone 2, Division 2.
  • Strain Gauge Bridge Transparent Repeater.
  • Up to four 350 Ω load cells in parallel or up to six 450 Ω load cells in parallel or up to twelve 1000 Ω load cells in parallel.
  • Broken field wire fault detection.
  • High Accuracy.
  • Three port isolation, Input/Output/Supply.
  • EMC Compatibility to EN61000-6-2, EN61000-6-4.
  • In-field programmability by DIP switch.
  • 250 Vrms (Um) max. voltage allowed to the Instruments associated with the barrier.

Discover D1000


STATUS

 
   PHASE-OUT
Next: SPARE-ONLY (2027-01-01)

Product lifecycle policy (EN)

ALTERNATIVE PRODUCT

CHANNELS

1

Request a free and personalized quotation!

Contact us

Technical Data


Supply
Voltage 24 Vdc nom (20 to 30 Vdc) reverse polarity protected, ripple within voltage limits ≤ 5 Vpp.
Current Consumption 80 mA with four 350 Ω load cells connected, typical.
Power Dissipation 1.7 W with 24 V supply and four 350 Ω load cells connected typical.
Max. power consumption at 30 V supply voltage and short circuit input, 2.8 W.

Input
Type up to four 350 Ω load cells in parallel or up to six 450 Ω load cells in parallel or up to twelve 1000 Ω load cells in parallel.
Bridge supply voltage 4.5 V nominal.
Bridge output signal ≤ 4 mV/V.
Input range ± 18 mV nominal span, ± 22 mV overrange.
Line resistance compensation ≤ 10 Ω.

Burnout
Type LED indication for field wire breakage.

Output
Type ± 20 mV nominal span, ± 24 mV overrange (5 V reference voltage), ± 40 mV nominal span, ± 48 mV overrange (10 V reference voltage).
Output impedance 350 Ω typical.
Host reference voltage ≤ 10 V typical, ≤ 11 V maximum.
Internal reference voltage 10 V typical, DIP switch settable.
Internal impedance 350 Ω typical, DIP switch settable.
Transfer characteristic linear based on mV input.
Response time ≤ 100 ms (10 to 90 % step change).

Performance
Type Ref. Conditions 24 V supply, 23 ± 1 °C ambient temperature.
Calibration accuracy ≤ ± 0.003 % of full scale of input range.
Linearity accuracy ≤ ± 0.002 % of full scale of input range.
Supply voltage influence ≤ ± 0.002 % of full scale for a min to max supply change.
Temperature influence ≤ ± 0.002 % of full scale of input range for a 1 °C change.

Isolation
Test Voltage I.S. In/Out 1.5 KV; I.S. In/Supply 1.5 KV; Out/Supply 500 V.

Environmental conditions

Operating temperature limits -20 to + 60 °C, relative humidity max 90 % non condensing, up to 35 °C.
Storage temperature limits – 45 to + 80 °C.

Safety description
Safety parameters Uo/Voc = 17.3 V, Io/Isc = 199.6 mA, Po/Po = 864 mW at terminals 9-10-11-12-13-14. Uo/Voc = 17.3 V, Io/Isc = 8 mA, Po/Po = 35 mW at terminals 13-14. Ui/Vmax = 30 V, Ci = 0 nF, Li = 0 nH at terminals 13-14. Um = 250 Vrms, -20 °C ≤ Ta ≤ 60 °C.

Mounting
Type EN/IEC60715 TH 35 DIN-Rail.
Weight about 165 g.
Connection by polarized plug-in disconnect screw terminal blocks to accomodate terminations up to 2.5 mm2.
Location Safe Area/Non Hazardous Locations or Zone 2, Group IIC T4, Class I, Division 2, Groups A, B, C, D Temperature Code T4 and Class I, Zone 2, Group IIC, IIB, IIA T4 installation.
Protection class IP 20.
Dimensions Width 22.5 mm, Depth 99 mm, Height 114.5 mm.

Data Sheet


Datasheet of D1063 ( EN )
D1000 Series Common Specifications and Dimensional Drawing ( EN )

Instruction Manual


Instruction Manual D1063 ( EN )
Instruction Manual D1000 Series ( EN | RU )
Ex safety instruction manual for D1000 series ( EN | IT )
INMETRO safety instruction manual for D1000 series ( PT )

Certifications


Type Description Area Number Issued by Issue Date
ATEX IMQ Zone 2 Applications D1000 Series Certificate ( EN ) Europe IMQ 09 ATEX 013 X IMQ 2022-05-03
ATEX Presafe ATEX for D1054, D1061, D1063 ( EN ) Europe Presafe 16ATEX8917 PRESAFE 2017-05-22
EMC D1000 EAC EMC Declaration of Conformity ( RU ) Eurasian Community ЕАЭС N RU Д-IT.НХ37.В.06311/20 EUROCERT 2020-08-13
Ex EAC Ex Certificate for D1000 Series ( RU ) Eurasian Community ЕАЭС RU С-IT.НА67.В.00113/20 TECHNOPROGRESS 2020-09-04
Ex FM No.3024643-3029921C Certificate ( EN ) North America 3024643-3029921C FM 2005-12-16
Ex INMETRO Certificate DNV 13.0135 X for D1054, D1061, D1063 ( EN ) Brazil DNV 22.0245 Rev. 0 DNV-GL 2022-12-10
IECEx IMQ IECEx Zone 2 Applications D1000 Series Certificate ( EN ) International IECEx IMQ 13.0011X IMQ 2022-05-03
IECEx Presafe IECEx for D1054, D1061, D1063 ( EN ) International IECEx PRE 16.0084 PRESAFE 2017-05-22
Maritime KR Maritime Certificate D1000 Series ( EN ) International MIL20769-EL001 KR 2022-07-04
Metrological Metrological Certificate Russia for D1000 Series ( RU ) Russia 64283-11 ROSSTANDART 2021-03-10

Declarations of Conformity


EU Declaration of Conformity for D1000 series (zone 2) ( EN | IT )
EU Declaration of Conformity for D1054, D1061, D1063 ( EN | IT )
EU Declaration of Conformity for RoHS, ASBESTOS. ( EN )
Declaration of G3 compliance for D1000_PSD1000-PSD1001-PSD1001C-PSD1004-PSD1220-PSD1220-098 SERIES ( EN )

Dimensions


Image of D1063_size

Connections


Drawings


2d_drawing_D1000_dwg ( EN )
3d_drawing_D1000_dwg ( EN )
3d_drawing_D1000_stp ( EN )